Arduino: If-else Statement (1 helpful way to learn)

by | May 6, 2022 | Arduino Uno projects

Introduction

Arduino: If-else Statement: Helpful 1 way to learn is the topic of this article in which I will develop the importance of The if-else statement is conditional in Arduino programming.

And explain that It is used to execute one of two blocks of code, depending on the value of a boolean expression.

The if(condition){statement}: Arduino: If-else Statement

Arduino If Statement is an example of a control flow statement in programming languages. It is used to make decisions and run different pieces of code based on the decision made.

The if() statement starts with “if.” It is followed by a condition, which can be any expression that evaluates whether true or false. If the expression evaluates to true, then the block of code that follows will be executed.

If it evaluates to false, then the block of code following will not be achieved.The condition evaluates as either true or false. If it evaluates to true, the code between the { } will execute. If it evaluates to false, the code between the { } will not run.

Conditional structure in programming

Conditional statements in c programming are used for decision-making.The structure of the conditional statement or the Arduino: If-else Statement is:if(condition){}else if ( condition){statement}else {statement}

Operators and if statement

Operators are the building blocks of any programming language. They are used to perform mathematical, logical, and relational operations. The if statement is a conditional statement used to control the flow of the program based on a specific condition.

The condition uses mathematical, logical, and relational operations to verify if the condition is met to execute the command or execute something else.

Serial monitor application1

Open the Arduino application, connect the Arduino to the computer and write the following code.void setup() {Serial.begin(9600);Serial.println(7==7);}void loop() {}

Comment on the code

*Upload the code from the Arduino Uno application.*Open the serial monitor*The serial monitor display 1*This means that if the result is true and 4 is equal to 4, the serial monitor display 1

Edit the code

write the following code.void setup() {Serial.begin(9600);Serial.println(7==9);}void loop() {}

Comment on the code

*Upload the code from the Arduino Uno application.*Open the serial monitor*The serial monitor display 0*This means that if the result is false and 7 is not equal to 9, the serial monitor display 0

Serial monitor application 2

Open the Arduino application, connect the Arduino to the computer and write the following code.int x = 27;int y = 7;void setup() {Serial.begin( 9600 );if(x>y){Serial.println(“true”); }}void loop() {}

Comment on the code

  • Upload the code from the Arduino Uno application
  • Open the serial monitor
  • The serial monitor display true
  • This means that if the condition is true (x>y), the serial monitor display true

Edit the code

int x = 27;int y = 7;void setup() {Serial.begin(9600);if(x<y){Serial.println (“true”); }else{Serial.println (“false”); }}void loop() {}

Comment on the code

  • Upload the code from the Arduino Uno application
  • Open the serial monitor
  • The serial monitor display false
  • This means that if the result is false and (x>y), the serial monitor displayfalse

Serial monitor application 3

Open the Arduino application, connect the Arduino to the computer and write the following code.int a = 5.5;void setup() {Serial.begin ( 9600 );if(a>0){Serial.println (“a is positive”); }else{Serial.println (“a is negative”); }}void loop() {}

Comment on the code

  • Upload the code from the Arduino Uno application
  • Open the serial monitor
  • The serial monitor display: a is positive
  • This means that if the result is true and (a>0), the serial monitor displaya is positive

Edit the code

Open the Arduino application, connect the Arduino to the computer and write the following code.int a = -5.5;void setup() {Serial.begin ( 9600 );if(a>0){Serial.println(“a is positive”); }else{Serial.println(“a is negative”); }}void loop() {}

Comment on the code

  • Upload the code from the Arduino Uno application
  • Open the serial monitor
  • The serial monitor display: a is negative
  • This means that if the result is false and (a<0), the serial monitor displaya is negative

Pushbutton Arduino project

We will use the pushbutton as an input for this project, and the LED as an output. If the user pushes the button, the result is true, and the LED is on.

The other case is that the result is false when the user does not push the button and the LED is off.

The code related to the project

Introduction

The components needed for this project are:

  • Arduino Uno board
  • Breadboard
  • Pushbutton
  • Two jumper wires

Circuit installation

Circuit installation

*Plug the red jumper wire into the pin 8 of the Arduino board*Connect the second side of the red jumper wire to the A1 leg of the pushbutton.*Plug the red-blue jumper wire into the ground pin of the Arduino board*Connect the second side of the blue jumper wire to the B1 leg of the pushbutton.

pushbutton as an input for this project 

The code of the project

const int pushButton = 8;const int led=13;void setup() {pinMode ( pushButton, INPUT_PULLUP);pinMode( led, OUTPUT);}void loop() {if(digitalRead ( pushButton ) == LOW ){digitalWrite ( led, HIGH);}else{digitalWrite ( led,LOW);}}

the user pushes the button, the result is true

LEDs Arduino Uno project

Circuit installation

  • Arduino Uno board
  • Breadboard
  • Pushbutton
  • Three blue jumper wires
  • Three red jumper wires

The code of the project

// C++ codeint pin2 =2 ;int pin8 =8 ;int a =15 ;int b =6 ;void setup(){pinMode ( pin2, OUTPUT);pinMode ( pin8, OUTPUT);}void loop(){if(a>b){digitalWrite ( pin2, HIGH);digitalWrite ( pin8, LOW);}}

Comment on the project

The LED on the right lights because the first condition is met.

The first edition of the LEDs Arduino Uno project

int pin2 =2 ;int pin8 =8 ;int a =5 ;int b =21 ;void setup(){pinMode (pin2, OUTPUT);pinMode ( pin8, OUTPUT);delay(1000);}void loop(){if(a>b){digitalWrite ( pin2, HIGH);digitalWrite ( pin8, LOW);}else{digitalWrite ( pin2, LOW);digitalWrite ( pin8, HIGH); }}

Comment on the project

The LED on the left lights because The second condition is met.

The second edition of the LEDs Arduino Uno project

The code

int pin2 =2 ;int pin8 =8 ;int a =5 ;int b =21 ;void setup(){pinMode (pin2, OUTPUT);pinMode ( pin8, OUTPUT);delay(1000);}void loop(){if(a==b){digitalWrite ( pin2, HIGH);digitalWrite ( pin8, LOW);}else{digitalWrite ( pin2, LOW);digitalWrite ( pin8, HIGH); }}

Comment on the project

The LED on the left lights because The second condition is met.The second editionof the LEDs Arduino Uno projectint pin2 =2 ;int pin8 =8 ;int a =5 ;int b =21 ;void setup(){pinMode (pin2, OUTPUT);pinMode ( pin8, OUTPUT);delay(1000);}void loop(){if(a!=b){digitalWrite ( pin2, HIGH);digitalWrite ( pin8, LOW);}else{digitalWrite ( pin2, LOW);digitalWrite ( pin8, HIGH); }}

Comment on the project

LEDs Arduino Uno projectThe LED on the right lights because The first condition is met.

The third edition of the LEDs Arduino Uno project

// C++ codeint pin4 =4 ;int pin7 =7 ;int pin11 = 11;int pinState11= digitalRead( pin11 );int a = 15 ;int b = 5 ;void setup(){pinMode( pin4, OUTPUT );pinMode( pin7, OUTPUT );}void loop(){if(a!=b){digitalWrite( pin4, HIGH);digitalWrite( pin7, LOW);delay(1000);}else{digitalWrite( pin4, LOW);digitalWrite( pin7, HIGH); }if(pinState11 == HIGH){digitalWrite( pin7, HIGH);delay(2000);}}

Combine two conditions to execute if statement

This section will explore how to execute if statement based on two conditions. The first condition is whether the variable a is equal to 10, and the second condition is whether the variable b is equal to 20.

If we want to execute an if statement only when both of these conditions are satisfied, we can use the following code:

Arduino: If-else Statementif (a == 10 && b == 20) {} else {}Code example// C++ codeint pin4 =4 ;int pin7 =7 ;int pin11 = 11;int pinState11= digitalRead( pin11 );int a = 15 ;int b = 5 ;void setup(){pinMode( pin4, OUTPUT );pinMode( pin7, OUTPUT );}void loop(){if(a!=b && a<b){digitalWrite( pin4, HIGH);digitalWrite( pin7, LOW);delay(1000);}else{digitalWrite( pin4, LOW);digitalWrite( pin7, HIGH); }if(pinState11 == HIGH){digitalWrite( pin7, HIGH);delay(2000);}}

Conclusion

The if() statement is a conditional statement. This means that it will only execute the statement if the condition is true.

An if statement can have an optional else clause that executes when the condition is false. The else clause must follow after endif at the end of the if() statement and have a corresponding else if() or else().

The syntax for an if() statement is as follows:if (condition) {statement;} else {statement; }

To conclude if(condition){statement} can be used in many different ways, including:

-To create loops, which are repeated statements executed until the condition becomes false.-To create conditional statements, which execute a certain statement only when the condition becomes true.

-To create decisions that execute one of two or more statements based on whether the condition becomes true or false.

Pin It on Pinterest

Share This